High-Speed Chip Shooter KE2070 KE2080 Daily Maintenance
Dec 14, 2021 Editor: admin
| Items to be checked | Check and lubrication frequency | ||||||
| Maintenance | Check Point | Check | Daily | Weekly | Monthly | Bimonthly | Every Year |
| Check | Air pressure |
Check that the air pressure is 0.5 MPa |
 |
||||
| Piping and joint | Air Leakage |
 |
|||||
| Unit air cylinder | Check operation |
 |
|||||
| Air Filter(Head) | No dirt |
 |
|||||
| Power on lamp | Check if it is lit. |
 |
|||||
| Transfer Belt | Worn Out, damage, or stretch |
 |
|||||
| Transfer Pulley | If it functions properly. |
 |
|||||
| Stopper Chip | worn out or damage. |
 |
|||||
| Gas Spring | Keep the front/rear safety cover opened |
 |
|||||
| Chip Box | Discard a chip(s) |
 |
|||||
| Cables and connectors | Check the connections. |
 |
|||||
| Vacuum Pump | Check the pressure. | Judge this check result by using the negative pressure gauge | |||||
| Cleaning | X- and Y-axis direct drive units | Remove dust and oil |
 |
||||
| Transfer belt | Remove dust and foreign substances |
 |
|||||
| Transfer sensors | Cleaning |
 |
|||||
| Laser align sensor | clean the sensor window |
 |
|||||
| EPV61/62(optional) | Cleaning of the lenses and LED lights |
 |
|||||
| Nozzle | Clean the nozzle |
 |
|||||
| Nozzle outer shaft | Clean the inside of the shaft |
 |
|||||
| ATC bracket | Remove dust and oil |
 |
|||||
| CVS(optional) | Remove dust and foreign substances. |
 |
|||||
| feeder bank, overall feeder exchange trolley | Remove foreign substances |
 |
|||||
| OCC(polarizing filter) | Remove dust and foreign substances |
 |
|||||
| VCS | clean the upper side |
 |
|||||
| CAL Block | remove dust and foreign substances |
 |
|||||
| Coplanarity(optional) | clean the sensor window |
 |
|||||
| Load control unit(optional) | Remove dust and foreign substances |
 |
|||||
| Fan Motor filter | Remove dust and foreign substances |
 |
|||||
| Lubrication | X- and Y-axis direct drive units rails | 6459 Grease N |
 |
||||
| Transfer screw shaft(shaft) | 6459 Grease N |
 |
|||||
| Transfer guide shaft | 6459 Grease N |
 |
|||||
| PWB stopper part | 6459 Grease N |
 |
|||||
| Ball Screw(head part) | CG2 Grease |
 |
|||||
| Spline shaft(head part) | CG2 Grease |
 |
|||||
| Nozzle | Oil | After cleaning | |||||
| Nozzle outer shaft | 6459 Grease N, Oil |
 |
|||||
| Overall feeder exchange trolley | 6459 Grease N |
 |
|||||
| Support table | CG2 Grease |
 |
|||||
| One Year = 6600 hours | |||||||
| Notes: | 1, For lubrication, use the attached oil or grease.For positions for which the use of only grease is specified,use the attached grease(6459 Grease N). | ||||||
| 2, Never apply any grease other than grease(CG2 Grease). to the parts to be lubricated with "Grease(CG2 Grease) | |||||||
|
3, New Defrix Oil No.1: Class four, third petroleum Grease(6459 Grease N): Not dangerous product regulated with the fire-defense law Grease (CG2 Grease): Not dangerous product regulated with the fire-defense law. |
|||||||